This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases. If you click a link and make a purchase, I may receive a small commission at no extra cost to you.
You can revive a Monstera adansonii by addressing its core needs and trimming away what’s no longer working.
If your plant is looking droopy, yellowing, or just plain sad, don’t worry because revival is totally possible in most cases.
The key to reviving Monstera adansonii lies in identifying the root cause, whether that’s overwatering, underwatering, or a lighting issue.
In this post, we’ll walk through the exact steps to bring your Monstera adansonii back to life and keep it thriving long-term.
Let’s dig into how to revive Monstera adansonii and get those iconic fenestrated leaves looking lush again.
Why Your Monstera Adansonii Might Be Struggling
Before you can revive Monstera adansonii, you need to figure out what’s stressing it out in the first place.
These plants are pretty hardy, but they’re also sensitive to sudden changes in their environment.
Overwatering is the most common culprit because it leads to root rot, which can be fatal if not caught early.
On the flip side, underwatering leaves the plant dehydrated, causing crispy brown edges and drooping stems.
Light is another big factor because too much direct sun scorches leaves while too little light slows growth dramatically.
So, the first step in reviving your Monstera adansonii is to play detective and check those three main areas.
Once you know what’s wrong, you can take the right corrective action and get your plant back on track.
1. Root Rot from Overwatering
When you overwater your Monstera adansonii, the roots sit in soggy soil and can’t get oxygen.
This leads to root rot, where the roots turn brown, mushy, and basically stop functioning.
If your plant smells musty or the stems are soft near the base, root rot is likely your issue.
To revive Monstera adansonii with root rot, you’ll need to unpot the plant and inspect the roots immediately.
Healthy roots are firm and white or tan, while rotten ones are dark and slimy to the touch.
Use sterilized scissors to snip away all the dead roots, leaving only the healthy ones behind.
Then, repot in fresh, well-draining soil and a pot with drainage holes to prevent future waterlogging.
2. Dehydration from Underwatering
If you’ve been neglecting your watering schedule, your Monstera adansonii will show clear signs of thirst.
Leaves will droop, curl inward, and develop brown, crispy edges that feel like paper.
To revive Monstera adansonii from dehydration, give it a thorough soak by watering until water runs out the bottom.
After that, let the top inch of soil dry out before watering again, but never let it stay bone dry for long.
You can also boost humidity by misting the leaves or placing a pebble tray with water underneath the pot.
Within a week or two, you should see new growth and the leaves perking back up to their normal position.
3. Inadequate Lighting Conditions
Monstera adansonii loves bright, indirect light, and it’ll tell you when it’s not getting enough.
If the leaves are small, pale, and leggy, your plant is probably reaching for more light.
To revive Monstera adansonii in low light, move it closer to a north or east-facing window.
Avoid direct afternoon sun because that can scorch the leaves and leave permanent brown patches.
If you don’t have great natural light, a grow light works wonders to boost photosynthesis and recovery.
Keep the light consistent once you find the right spot, because constant moving will stress the plant further.
Step-by-Step Guide to Revive Monstera Adansonii
Now that you know the common issues, let’s walk through a practical, step-by-step revival plan.
This method works for most situations as long as there’s still some healthy tissue left on the plant.
Follow these steps and you should see measurable improvement in your Monstera adansonii within a few weeks.
1. Prune Dead or Damaged Leaves
Get your clean, sharp scissors and remove any yellow, brown, or fully dead leaves from your Monstera adansonii.
Cut at the base of the stem where it meets the main vine, being careful not to damage healthy nodes.
Pruning is essential to revive Monstera adansonii because it redirects energy to the healthy growth points.
Don’t be afraid to cut aggressively if needed, because these plants bounce back quickly from a good trim.
Once you remove the dead weight, the plant can focus on producing new leaves and roots instead.
2. Check and Refresh the Soil
If your soil is compacted, waterlogged, or seems to be holding water for too long, it’s time for a change.
Gently remove the plant from its pot and shake off the old soil from the roots.
Inspect the roots again for any rot, and trim any suspicious parts you missed the first time.
Repot your Monstera adansonii in a mix of potting soil, perlite, and orchid bark for great aeration.
Make sure the new pot has drainage holes and isn’t too big, because excess soil holds excess moisture.
This fresh start can be the single most effective way to revive Monstera adansonii that’s been struggling.
3. Water with Care and Consistency
After repotting, water your Monstera adansonii lightly to settle the soil around the roots.
Then, establish a watering routine based on the soil’s moisture, not a strict calendar schedule.
Stick your finger about an inch into the soil, and only water when that top inch feels dry.
Overwatering at this stage will undo all your hard work, so err on the dry side if you’re unsure.
You can also use a moisture meter if you want a more precise reading to guide your watering.
Consistency is key as you revive Monstera adansonii, because erratic watering stresses the roots.
4. Provide the Right Environment
Place your Monstera adansonii in a spot with bright, indirect light and stable temperatures between 65–80°F.
Keep it away from drafty windows, air conditioners, and heating vents that cause temperature swings.
Humidity should be above 50%, so consider using a humidifier if your home is dry.
You can also group it with other plants to create a more humid microclimate naturally.
Patience is your best friend here, because it can take two to four weeks to see visible signs of recovery.
Don’t fertilize during this recovery phase, because the roots are stressed and can’t handle the extra salts.
How to Revive Monstera Adansonii in Water Roots
If you’ve been rooting cuttings in water, the revival process looks a little different.
A Monstera adansonii in water can still struggle if the water is stagnant or the roots are rotting.
To revive Monstera adansonii in water, change the water completely every five to seven days.
Use filtered or distilled water, because chlorine and fluoride in tap water can harm the roots.
If any roots look brown and mushy, trim them off and gently rinse the healthy roots under lukewarm water.
Then, place the cutting in a clean jar with fresh water, ensuring no leaves are submerged.
Keep the jar in bright, indirect light and watch for new white root growth as a sign of revival.
Once the roots are several inches long, you can transition it to soil using the steps above.
So, How Do You Revive Monstera Adansonii?
You can revive Monstera adansonii by fixing the root cause, pruning damaged parts, and giving it proper care.
Start by checking for root rot or dehydration, then adjust light, water, and humidity accordingly.
Repotting in fresh soil and cutting away dead leaves will give your plant the fresh start it needs.
With consistency and patience, your Monstera adansonii will push out new growth and look vibrant again.
Remember to water only when the top inch is dry and provide bright, indirect light at all times.
So if your plant is looking rough, don’t give up hope because revival is very much achievable.
Follow these tips and soon you’ll see why Monstera adansonii is such a rewarding plant to own.